Aprilaire Outdoor Temperature Sensor Installation

AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for

Say goodbye to rooms that fluctuate uncomfortably between too cold and too hot. • use to monitor water by affixing it to outside of water pipe and insulate. Web for aprilaire® humidifier installation, follow aprilaire humidifier installation instructions. • can also be used to control floor temperature (requires clipping metal bracket). Web your aprilaire humidifier control is installed in the.

AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for

It is important to anticipate a drop in outdoor temperature and reduce the setting accordingly to avoid excessive condensation. The sensor can be used with the aprilaire 8570, 8870 or 8600 thermostats. Web installation outdoor temperature sensor (optional) outdoor temperature can be measured by attaching an 8052 sensor to the sl and s2 terminals. If an ahc is to be.

AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for

• do not mount closer than three feet to any exhaust vent. If an ahc is to be installed. • do not route wire alongside 120vac wires. A second sensor located on the outdoor coil is used to measure the coil temperature. • optional wireless outdoor temperature sensor available.

AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for

Web • heat blast® raises the room temperature 3°f to 5°f. Web my aprilaire 600 humidifier was installed with the outdoor temperature sensor placed in an inlet air duct (6 diameter, insulated, running about 12 feet to the outside wall). Or should the sensor go all the way to the outside. Locate the aprilaire model 8052 sensor on the side.

Aprilaire 8052 Outdoor & Duct Mount Temperature Sensor

• do not route wire alongside 120vac wires. Web outdoor temperature sensor (optional) outdoor temperature can be measured by attaching an 8052 sensor to the s1 and s2 terminals. A second sensor located on the outdoor coil is used to measure the coil temperature. Place at least 3' away from exhaust vents and condensing lines. Web installation outdoor temperature sensor.

Aprilaire Outdoor Temperature Sensor Installation - • use to monitor water by affixing it to outside of water pipe and insulate. Web heat pump units use the outdoor air temperature sensor to shut down the heat pump and go to auxilary heat when the outdoor temp drops below a certain set point (usually set at around 35f) most standard heat pump units are inefficient below 35f although some have been designed to produce heat at much lower temps. System setting #05 (remote sensor) is used to enable sensor. Web outdoor temperature sensor (odt) the temperature sensor can be located in the fresh air duct, in the vent inlet, or on the outside of an exterior wall. Place above the snow line. Do not install inside outdoor condensing unit.

Experience consistent, balanced temperatures throughout your home by utilizing the t9's smart room sensors. Web outdoor temperature sensor (optional) outdoor temperature can be measured by attaching an 8052 sensor to the s1 and s2 terminals. Locate the aprilaire model 8052 sensor on the side of the building out of direct sunlight (see figure 3). Web my aprilaire 600 humidifier was installed with the outdoor temperature sensor placed in an inlet air duct (6 diameter, insulated, running about 12 feet to the outside wall). Do not install inside outdoor condensing unit.

Save This Manual For Future Reference.

• optional wireless outdoor temperature sensor available. System setting #05 (remote sensor) is used to enable sensor. Web heat pump units use the outdoor air temperature sensor to shut down the heat pump and go to auxilary heat when the outdoor temp drops below a certain set point (usually set at around 35f) most standard heat pump units are inefficient below 35f although some have been designed to produce heat at much lower temps. If an ahc is to be installed.

Place At Least 3' Away From Exhaust Vents And Condensing Lines.

Say goodbye to rooms that fluctuate uncomfortably between too cold and too hot. Web installation outdoor temperature sensor (optional) outdoor temperature can be measured by attaching an 8052 sensor to the sl and s2 terminals. • when the outdoor temperature is less than the low Web outdoor temperature sensor (odt) the temperature sensor can be located in the fresh air duct, in the vent inlet, or on the outside of an exterior wall.

Place Above The Snow Line.

Or should the sensor go all the way to the outside. Web for aprilaire® humidifier installation, follow aprilaire humidifier installation instructions. Unpack the humidifier control carton. A second sensor located on the outdoor coil is used to measure the coil temperature.

Web Outdoor Temperature Sensor (Optional) Outdoor Temperature Can Be Measured By Attaching An 8052 Sensor To The S1 And S2 Terminals.

Do not install inside outdoor condensing unit. • do not use more than 300 feet of wire to For example, with an outdoor temperature of 20° the correct setting will be 35% relative humidity. Place above the snow line.